# Questions tagged [current]

Flow of electric charge - typically movement of charge carriers, such as electrons. Measured in amperes (A).

25 questions
Filter by
Sorted by
Tagged with
22 views

### How dangerous are HASEL artificial muscles with its Kv requirements?

So, I don't know much about electricity and this kind of stuff, so I hope I don't make too many misconceptions. What are HASEL artificial muscles? It is a “Hydraulically amplified self-healing ...
• 113
87 views

### Inner current controller benefits

I am currently working on a system with a BLDC motor attached to a non linear spring on which a user can apply a force. Meaning the torque applied on the motor's output is most of the time unknown. ...
• 31
1 vote
3k views

### How to calculate Current for pancake stepper motor - To change in Pronterface

DISCLAIMER: New to electrical engineering topics. I'm a 3d-printing hobbyist. I don't know all the Jargon being used but trying my best to keep up. PROBLEM Recently bought a Nema 17 stepper pancake ...
• 13
1 vote
54 views

### How to pick the right motor driver?

I have this brushed DC motor (Vex 775pro: https://motors.vex.com/vexpro-motors/775pro; motor curve data here I assume is useful but I do not exactly know how to make sense of it) My question is, how ...
45 views

### Can I use a breadboard to power multiple SG90 servos?

I am planning on using 10 Towerpro SG90 servos, which operate at 4.8V or 6V and can require a maximum stall current of 700ma. If I use a breadboard like this one (https://www.amazon.com/gp/product/...
• 101
106 views

### How can a motor be run at higher voltage for longer?

A 12V windshield wiper motor to run at 24V for more speed but near-equal driving force. Testing with a variable DC supply between 21.6V & 26.4V showed the current maxes at 3.72 - 3.90A, as ...
• 11
1 vote
141 views

### Powering servos for quadruped spiderbot using arduino uno [closed]

I am using 12 towerpro SG90 servos. What battery should I use for powering 12 servos for my arduino uno? Can i use the 12v battery, plug it in to 12v dc jack of arduino and tap the 5v output of ...
1k views

### How to deal with current spikes due to fast direction-switching motor commands?

I'm trying to build a self-balancing two-wheeled segway-like robot. I'm currently using two 12v DC motors that draw approximately 600milliamps of current each. I've noticed that when my robot tries ...
• 1,238
5k views

### Servo motor power consumption issue

I am using servo motor model no. MG995 with Arduino. I don't know the current it consumes while powered on and while lifting a 10 kg of weight. I am currently using a 5 V, 1 A power supply with one ...
522 views

### DC gearmotor stall current and battery capacity

I'm working on a self-balancing robot project and am in the process of motor sizing. I've read that with self-balancing robots the motors need to switch direction quickly, which can cause them to ...
• 155
1 vote
62 views

### Electronic speed controllers and total current draw

Do we have to take Electronic Speed Controllers (ESC) into account when calculating the total current draw of the system? As far as I can understand, the motor and ESC are connected in series, so we ...
• 113
1 vote
417 views

### Brushless DC motor problems at high velocities

For a project we use a brushless DC (BLDC) motor. Everything works fine until we tried to reach high velocities. I will first explain my setup, and than explain our problems using some graphs. 1.0 ...
• 75
245 views

### what is the difference between a voltage source and current source? [closed]

I know,this question is irrelevant.But,while working suddenly this question came through my head..my point is there should not be any difference between a voltage source and a current source.cause,...
• 195
118 views

### How to test how much current 9 servos can draw at a time? [closed]

Plus how should I use a multimeter to test it? P. S. Really sorry for a noon question.
612 views

### What are some ways to estimate torque/load on a robotic arm joint

My main problem is measuring joint torque/load economically. There are ways to detect the electric current drawn which is proportional to the torque. Since my motor is a BLDC motor, there will be a ...
• 181
1 vote
1k views

### Can too much input current destroy my motor driver?

I have a 18 V rated driver I'm using to drive two 12 V DC gear motors using my Arduino. I bought a new battery pack which is rated 3300 mAh 25C, 11.1V making the total current input 82.5 A. My driver ...
3k views

### How can I reduce a motor's maximum current draw?

I have a motor with a stall current of up to 36A. I also have a motor controller which has a peak current rating of 30A. Is there any way I could reduce the stall current or otherwise protect the ...
148 views

### Comparison of the efficiency of DC motor current limiting / control methods?

I am using the wheels and motors of an RC toy car as a simple robotics platform. The car has 2 motors, one drives the back wheels, the other steers the front wheels. The steering motor is stalled by ...
212 views

### Power switch standards and suitability for purpose

I scavenged a 4 terminal power switch (Legion EPS 21) from some electronic device (don't remember what it was) and it has the following markings on it: Legion EPS21 10A 250VAC TV-5 8A/128A 250V &...
• 351
1 vote
725 views

### Can't Read current on Pololu Dual MC33926 Motor Driver Shield for Arduino

I purchased a Pololu Dual MC33926 Motor Driver Shield for Arduino, and for some reason I cannot read current from the motor controller. On the Serial.println() it just prints weird data (garbage), and ...
• 203
998 views

### Arduino with two Linear Actuators, two ACS714 Current Sensors, and an L298N Motor Driver setup

I am using the L298N motor driver to drive two HAD1 linear actuators (12V each and a no-load drive current of ~950mA each) Linear Actuator: http://www.alibaba.com/showroom/mini-linear-actuator-had1....
• 203
1 vote
192 views

### Motor driver selection

I am building a 2 wheel robot to carry 7KG of load. I used this link to get the torque required for each motor which is 11Kg-cm. So I choose 2 of these motor which has 36Kg-cm(2x more) torque. I ...
19k views

### How to tell a stepper motor's position, or detect slippage

I am creating a CNC machine on a budget, using old motors out of printers/scanners/etc. I am limited to about 650mA for the whole system, so my fear is that when the cutting bit touches the material,...
3k views

### Arduino Vin Current Limit

I've found that Arduino (Duemilanove) has a current limit of 40mA per pin. Does this include the Vin pin? Or does the Vin pin have some sort of work around in place on the board to allow for higher ...
• 1,504