All Questions

Tagged with
Filter by
Sorted by
Tagged with
0
votes
0answers
19 views

How do I know if a wheel and stepper motor fit together?

Looking for some wheels and a stepper motor to make a self balancing robot. How do i know if the stepper motor shaft can fit in the wheels? I cant find the shaft diameter when looking at some ...
0
votes
1answer
522 views

Wall following robot oscillates heavily

I have a mapping robot , 3 ultra sound sensors HC SR04 , arduino uno board, two motors MG-6-120, power source 2 5v 4000 mAh power banks, driver L298N. It uses a wall follower algorithm (here is the ...
0
votes
1answer
45 views

How Do You Program the SR04 Ultrasonic Sensor?

Dear Robotics Community, I am participating in a Robotics tourney that will start in a few weeks. The challenge I signed up for is to deliver and dump ping pong balls to a box. I already have my ...
0
votes
2answers
234 views

How to locate an object on a known surface

I am building a small robot on wheels. The robot will be moving at a small speed in a square area of known dimensions. I need to locate the robot and know its position at any given moment so I can ...
3
votes
2answers
422 views

Two-wheeled self-balancing robot - Choosing the control system

Would an Arduino Uno have the precision-timing required (using only firmware) to control a two-wheeled inverted pendulum robot, or would it need a RTOS? Note: Thanks for both answers, they both ...
2
votes
1answer
956 views

Arduino robot to move spirally

I am planning to build robot like irobot Roomba. So cleaning in a spiral pattern is required like the image shown starting from the center: This code is part of my full code which doesn't give me ...
0
votes
3answers
4k views

How to go around in a circle?

I have the mBot robot and I'm trying to get it to go to the other side of a cylindral obstacle. Something like this: What I know: Radius of the cylinder - r Robot's distance from the cylinder ...
1
vote
1answer
5k views

Making a car go straight [duplicate]

I'm trying to work a car that's being controlled by an Arduino. I'm using the following chassis: New 2WD car chassis DC gear motor, wheels easy assembly and expansion and an L298N motor driver. The ...
0
votes
2answers
839 views

Arduino project: Turning with a fixed front wheel axis

I am working on an Arduino robot project. This project requires a base with 4 wheels where the back wheels are attached to two DC motors that can be controlled independently of each other. I am ...
0
votes
1answer
1k views

Balancing Robot Control Model

I am trying to find a control model for the system of a balancing robot. The purpose of this project is control $\theta_2$ by the 2 motors in the wheels i.e. through the torque $τ$ I started with the ...
0
votes
2answers
861 views

Looking for a cheap(ish) micromouse that I can program with C/C++ [closed]

I'm looking to buy a micromouse (i.e. a small single-board unit with wheels and IR sensors that can move around freely). I've done a lot of searching but have only found resources relating to building ...
1
vote
1answer
83 views

How to find the height of a rock with a rover?

So, I am designing a rover that will navigate to a rock, and then calculate the height of the rock. Currently, my team's design involves using an ultrasonic rangefinder and lots of math. I was ...
2
votes
2answers
1k views

Can I make an automatically-parking robot car with IR sensor?

It would be easy to understand if you imagine a robotic vacuum cleaner. (For some models) It goes back to a specific place automatically to recharge. Like this, I want to make a robot which ...
5
votes
1answer
4k views

12V compressor and air pressure control

I am trying to make a simple robot with few functionality for someone, one of these functionality is inflating a balloon inside the robot, I know how to control a compressor using Arduino but the ...
7
votes
2answers
3k views

Cascading PID DC Motor Position & Velocity Controllers

I'm trying to build a robot with a differential drive powered by two DC Motors. First I implemented a PID Controller to control the velocity of each motor independently. Estimated the TF using the ...
10
votes
3answers
22k views

What are the signs that a servo might be broken?

I just got a kit and im not sure if its me or not but it appears one of the continuous servos might be broken. What happened first when I plugged it into the microcontroller, it made a humming sound ...