All Questions

Tagged with
Filter by
Sorted by
Tagged with
0
votes
0answers
22 views

Using Simulink Interpreted MATLab fcn for robot dynamics using Robotics Toolbox

I am using Interpreted MATLab fcn to compute forward dynamics. I am using code of accel in which I have added my robot model in the beginning, making the accel function: ...
0
votes
0answers
18 views

3 DOF robot torque not converging Robotics Toolbox

I have a Simulink model in which desired torque is [0;0;0] and current torque should converge to zeros too. But I am getting oscillatory torque as output. This is the block diagram of what I am ...
3
votes
1answer
60 views

3-DOF Robot Dynamics error in Robotics Toolbox

I am trying to compute dynamics of 3 DOF robot using Robotics Toolbox by executing this code: robot.accel(q, zeros(1,3), zeros(1,3)) But I am getting this error: ...
2
votes
0answers
40 views

how to introduce 2 inputs into a matlab block function that processes only one variable at a time? [closed]

Using SIMULINK, I wanted to optimize 2 variables with the ant colony optimization algorithm; which is written in a matlab function block, the function is of type function y = f (x) it has only one ...
2
votes
1answer
450 views

Euler-Lagrange Dynamic model

I'm working on a masters thesis and need to calculate Mass inertia matrix ($M$), Coriolis/Centrifugal matrix ($C$), and the gravity matrix ($G$) in the equation $M\ddot{\theta} + C\theta + G = \tau$ (...
1
vote
2answers
763 views

Inverse dynamics for robotic arm using Matlab Simmechanics

I am learning Simmechanics Matlab to do inverse dynamics for 4 DOF robotic arm. I read many examples to input motion to revolute joints like through PID, slider gain, sine waves, signal Builder etc. ...
0
votes
2answers
394 views

Mathematical modelling of system dynamic on matlab

I want to make a matlab (simulink) control model for the system in the image below. The original pdf is only accessible if logged in Carleton's Learning Management System. How do I get the dynamics ...
1
vote
3answers
607 views

How to apply A bang-bang signal of amplitude 1 N and 1 s width as an input force to reproduce certain results in Matlab?

I working on dynamic modeling and simulation of a mechanical system (overhead crane), after I obtained the equation of motion, in the form: $$ M(q)\ddot{q}+C(q,\dot{q})\dot{q}+G(q)=Q $$ All the ...
0
votes
1answer
87 views

Dynamic Model of a Manipulator

I'm stuck on equation 4.30 of page 176 in http://www.cds.caltech.edu/~murray/books/MLS/pdf/mls94-complete.pdf This equation: $\frac {\partial M_{ij}} {\partial \theta_k} = \sum_{l=\max(i,j)}^n \Bigl( ...
4
votes
1answer
174 views

Calculating required torques for a given trajectory using Lagrange-Euler

I have a 2DOF robot with 2 revolute joints, as shown in the diagram below. I'm trying to calculate (using MATLAB) the torque required to move it but my answers don't match up with what I'm expecting. ...
1
vote
3answers
247 views

Dynamic simulation of compliant elements in quadruped robot

I have a preliminary design for a legged robot that uses compliant elements in the legs and in parallel with the motors for energy recovery during impact as well as a pair of flywheels on the front ...
1
vote
1answer
216 views

Matlab: System simulation with dynamic state matrix / input matrix [closed]

I have the following system: $$\dot{x} = A(t)x+B(t)u$$ $$y = x$$ $A(t)$ and $B(t)$ are actually scalar, but time-dependent. If they would be constant, I could simulate the system in Matlab using: <...
1
vote
4answers
220 views

Why I'm getting very long terms in the inertia matrix (or dynamics model) of the robot using matlab script?

I'm working on the dynamics model of a RRRR articulated robot, I'm following Euler-Lagrange approach and developing my code in m-file in matlab; I'm looking for dynamic model of this form: $$ D(q) \...