Questions tagged [irobot-create]

The iRobot Create is a programmable robot based on the Roomba vacuuming robot. Users can program it using the iRobot Open Interface.

16 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
115 views

Roomba iRobot Create 2 Open Interface, is there a way to turn off vacuum motor while the robot is docking?

I am able to control every desired aspect of my robot, except for vacuum motor which seems to be turned on for some reason every time I send Seek Dock (code ...
2
votes
0answers
91 views

Waking Up Roomba Over Serial

Sorry if this is a noobie question, it's my first time posting on this forum... I've been trying to mod an old Roomba 400 series (model #4220) by adding a raspberry pi to it. (I know real original ...
2
votes
2answers
86 views

problem of power on PIN 1 and PIN 2 of DIN connector of Roomba 521

I notice there is a problem of power on PIN 1 and PIN 2 of DIN connector of Roomba 521...I have only 0,5 V but it's expected 12V...motherboard damaged?
2
votes
1answer
210 views

IRobot 690 - raw wheel encoder counts change with no movement command issued

I am using a Raspberry Pi 3, B+ pertinent libraries are WiringPi, with WiringSerial. Code is written in c. EDIT: the Serial connection is handled through GPIO 14(Tx) & 15(Rx), 5v (Tx) is stepped ...
1
vote
1answer
70 views

Does the roomba 675 have the same open interface spec and as the roomba create 2?

I see that the create 2 spec says it is based on the roomba 600 series, but I don't know if they are the same or if I should expect differences. I want to send it a command to get it to turn around ...
1
vote
0answers
129 views

increase current draw from serial port of icreate 2

This is from the icreate 2's document: "Pins 1 and 2 (Vpwr) are connected to the Roomba battery through a 200 mA PTC resettable fuse. The continuous draw from these two pins together should not exceed ...
1
vote
0answers
382 views

Power on iRobot Create 2 via serial port

I have Arduino talk with Create 2 via serial interface. But before sending commands to the robot, I have to power it on by manually pushing the power button on the robot. How to make the robot turned ...
0
votes
1answer
81 views

How can I control an Irobot Create using Jetson Nano?

I have an irobot create 4400 model and I'm trying to use a jetson nano to send commands to it. I want to try this example that turns on the play led. I connected the tx and rx and gnd ports from J41 ...
0
votes
0answers
70 views

Connecting to iRobot Create 2 serial port over WebUSB

I am attempting to connect to the supplied USB serial cable that came with iRobot Create 2 from Chromium 78.0.3904.108 (32-bit) on a Raspberry Pi 4. From lsusb, I ...
0
votes
0answers
33 views

problem roomba 500 power saving scheduler

anybody experienced problem with power saving and scheduler command? I have roomba 521 with last firmware updated via OSMO, so now it has also power saving feature. I have problem with scheduler ...
0
votes
1answer
153 views

Roomba stops responding to commands on the OI

So I just received my roomba create 2. I have managed to read and send commands to the roomba using the OI and an Arduino. I also got it to move using the USB cable provided by iRobot and the tethered ...
0
votes
0answers
62 views

Can't get iRobot Create to respond

We have an iRobot Create connected to a Win 10 PC with the cable supplied with the unit. We have followed the instructions here: http://www.robotappstore.com/Knowledge-Base/How-to-Use-a-RealTerm-...
0
votes
2answers
287 views

Driving the iRobot Create 2 straight

I am attempting to make the iRobot Create 2 drive in a straight line using the opcode 137 with the parameters specified in the OI documentation. "Straight = 32768 or 32767 = 0x8000 or 0x7FFF" I have ...
0
votes
0answers
57 views

Issues with Running Multiple Instructions in Sequence

I tried to use Microsoft Robotics Dev Studio (sample 4) to write a code that was able for robot to go with a square path by just one clicked. However, there is one problem. When I try to put ...